| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-4SFP25G-AOC1M | |
| 2 | Arista Networks | AOC-Q-4S-100G-1M | |
| 3 | Dell | AOC-Q28-4SFP28-25G-1M | |
| 4 | Juniper Networks | JNP-100G-AOCBO-1M | |
| 5 | NVIDIA/Mellanox | MFA7A50-C001 | |
| 6 | H3C | QSFP28-4SFP28-AOC-1M | |
| 7 | Brocade | 100G-Q28-S28-AOC-0101 |
Key Technical Specifications
| Cisco Compatible |
QSFP-4SFP25G-AOC1M
|
Vendor Name | HYTOPTODEVICE |
| Connector | QSFP28 to 4 x SFP28 | Max Data Rate | 100Gbps |
| Operating Wavelength | 850nm | Fiber Cable | OM3 MMF |
| Cable Length | 1m (3ft) | Power Consumption | 2.2W (QSFP28 End) 0.8W (SFP28 Per End) |
| Jacket Material | OFNP | Operation Temperature | 0~ 70 °C (32 to 158°F) |
| Minimum Bend Radius | 30mm | Protocols | QSFP28 MSA, SFP28 MSA |
| Application |
25G/100G Ethernet, InfiniBand QDR
|
Warranty | 5 Years |
Usage Guidelines & Best Practices
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Devices
Built on universal MSA open standards, this cisco compatible qsfp28 breakout cable supports mixed-vendor networking hardware. can interoperate with mainstream network brands including Arista, H3C, Juniper, Dell, NVIDIA Mellanox and more, for mixed-vendor rack stacking and server fabric expansion.





Q1: What bending guidelines should I follow when routing the four SFP28 breakout tails of this 1m QSFP28 breakout AOC? A: Maintain a minimum bend radius of roughly 30mm at all times. Sharp bends beyond this limit will crack internal glass fibers and permanently break the link of this cisco compatible qsfp28 breakout cable from our supplier.
Q2: Can this 100G breakout AOC deliver full bidirectional 100Gbps aggregate throughput across all four 25G lanes? A: Yes, it supports full wire-speed 100Gbps bidirectional transmission, with four independent 25G channels running at full speed without bandwidth reduction.
Q3: Will short-distance 1-meter transmission introduce timing jitter and impact link stability? A: No. Integrated CDR chips inside optical transceivers actively suppress jitter and sustain an ultra-low bit error rate for reliable short-range data center transmission.
Q4: Can I configure each SFP28 breakout port to run at different speeds for mixed-rate networking deployment? A: No. The 100G QSFP28 input port is fixed to four 25G channels. Individual breakout legs cannot be adjusted to 10G or 50G speeds separately.
Q5: What switch warning logs indicate an EEPROM coding mismatch on this Cisco compatible QSFP28 breakout AOC? A: Typical alerts include "Unsupported transceiver detected", "Security checksum error", or "Unqualified optic detected", which signal incompatible vendor programming.
Q6: Are these 25G SFP28 breakout tails backward compatible with older 10G SFP+ ports on Cisco switches? A: No. SFP28 hardware is designed natively for 25G operation and lacks auto-negotiation to drop down to 10G SFP+ speeds.
Q7: What happens if I mistakenly insert the main QSFP28 plug into a 40G QSFP+ port? A: QSFP28 follows 100G electrical specifications. It cannot establish stable connectivity inside a native 40G QSFP+ port without dedicated signal conversion adapters.
Q8: Which Cisco CLI commands can verify all four breakout sub-channels are successfully identified? A: You can run commands such as show interface status or show inventory to confirm all four breakout sub-interfaces appear in the port inventory list.
Q9: Is it possible to daisy-chain multiple QSFP28 breakout AOCs to extend the cabling distance for rack deployment? A: No. Active optical breakout cables cannot be cascaded. Series interconnection breaks the optical path and triggers total link failure.
Q10: What troubleshooting steps should I take when only three breakout lanes become active after installation? A: Validate the Cisco switch breakout configuration, reseat each SFP28 connector firmly, and review DOM diagnostic readings to locate the faulty optical lane.
Q11: Will squeezing or accidental pressure on the outer jacket damage the internal fiber strands of this breakout AOC? A: Yes. Crushing force can fracture internal glass fibers. The outer jacket may remain intact while the optical transmission path is permanently destroyed.
Q12: Does this compact 1m breakout AOC add weight and cause port sag on Cisco switch slots? A: No. AOC fanout cables are much lighter than copper breakout variants, removing mechanical strain and port sag risks on switch hardware.
Q13: Is field splicing or local repair possible if the cable jacket gets pinched or cut during rack installation? A: No. Transceivers are pre-integrated into the cable assembly. On-site splicing is not practical, and damaged AOC units require full replacement.
Q14: What after-sales support can I access if bulk breakout AOC arrives with incorrect vendor EEPROM coding? A: As your cisco compatible qsfp28 breakout cable supplier, HYTOPTODEVICE provides exchange, return or re-programming service for coding compatibility issues upon delivery.
Q15: Can I request custom non-standard cable lengths instead of stocked standard sizes for my procurement project? A: Standard lengths including 1m,3m,5m,7m,10m,15m,20m are kept in stock. Custom lengths are available for enterprise orders subject to MOQ rules.
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every transceiver is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.






