| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-4X10G-AOC15M | |
| 2 | Arista Networks | QSFP-4X10G-AOC15M | |
| 3 | Dell | CBL-QSFP-4X10G-AOC15M | |
| 4 | Juniper Networks | JNP-QSFP-AOCBO-15M | |
| 5 | Extreme | 10GB-4-F15-QSFP | |
| 6 | H3C | QSFP-4X10G-D-AOC-15M | |
| 7 | Brocade | 40G-QSFP-4SFP-AOC-1501 |
| Cisco Compatible |
QSFP-4X10G-AOC15M
|
Vendor Name | HYTOPTODEVICE |
| Connector | QSFP+ to 4 SFP+ | Max Data Rate | 40Gbps |
| Operating Wavelength | 850nm | Fiber Cable | OM3 MMF |
| Cable Length | 15m (49ft) | Power Consumption | ≤1.4W |
| Jacket Material | OFNP | Operation Temperature | 0~ 70 °C (32 to 158°F) |
| Minimum Bend Radius | 30mm | Protocols | 10G/40Gigabit Ethernet or Fibre Channel |
| Application |
InfinibandQDR/DDR/SDR,40G Ethernet,Data Center,Fibre
Channel
|
Warranty | 5 Years |
Usage Guidelines & Best Practices
Mandatory Port Breakout Configuration: Ensure the host QSFP+ port supports channelization. Enable breakout mode (4x10G) via the switch CLI before connecting the cable.
Cabling Requirements: Do not exceed the minimum 30mm bend radius, avoid sharp folding, heavy extrusion or long-term tension on the cable assembly.
Port Installation Standard: Do not mix this breakout AOC with straight QSFP+ to QSFP+ AOC configuration.
Hot‑swap rule:Never pull or tug directly on the individual breakout legs. Always use the integrated pull-tab or bale latch when inserting or removing connectors.
Operating Environment: 0‑70℃, indoor cabinet deployment only.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Devices
Built on MSA open standards, this cisco QSFP+ to Four SFP+ AOC Active Optical Cable supports mixed-vendor networking devices. can interoperate with mainstream network brands including Arista, Brocade, Juniper, Dell, H3C and Fortinet, for mixed-vendor rack stacking and server fabric expansion.




Q1: What is the minimum bend radius I need to keep when routing the breakout pigtails of this 15m AOC? A: Maintain a minimum bend radius of around 30mm at all times. Sharp bends beyond this limit will crack internal glass fibers and permanently break the link of this cisco qsfp+ to four sfp+ aoc active optical cable from our supplier.
Q2: Can this 40G breakout AOC deliver full duplex 40Gbps bandwidth simultaneously across all four lanes? A: Yes, it supports full wire-speed 40Gbps aggregate throughput in both directions, with four separate 10Gbps channels running independently without bandwidth reduction.
Q3: Will extended 15-meter transmission introduce noticeable signal jitter that hurts link performance? A: No. Integrated CDR circuits inside the optical transceivers actively suppress jitter and sustain an ultra-low bit error rate for stable long-distance data transmission.
Q4: Can I configure each breakout tail to run at different speeds for mixed-rate networking deployment? A: No. The 40G QSFP+ port is fixed to split into four 10G channels. Individual SFP+ legs cannot operate at 1G or 25G speeds separately.
Q5: What switch warning messages indicate an EEPROM coding mismatch on Cisco-compatible breakout AOC? A: Typical alerts include "Unsupported transceiver detected", "Security checksum error", or "Unqualified optic detected", which signal incompatible vendor programming.
Q6: Can these 10G SFP+ breakout tails work with older 1G SFP ports on legacy Cisco switches? A: No. SFP+ hardware is designed for native 10G operation and lacks auto-negotiation capability to drop down to 1G SFP speeds.
Q7: What will happen if I mistakenly insert the QSFP+ main connector into a 100G QSFP28 port? A: QSFP+ follows 40G electrical specifications. It cannot establish stable connectivity in a 100G QSFP28 port unless paired with dedicated downshifting adapters.
Q8: How can I confirm that the Cisco switch successfully recognizes all four breakout sub-channels? A: Execute CLI commands such as show interface status or show inventory, to verify all four breakout sub-interfaces appear within the switch’s port list.
Q9: Is it possible to connect multiple breakout AOCs in series to achieve longer cabling distances? A: No. Active optical breakout cables cannot be daisy-chained. Series interconnection breaks the optical path and results in total link failure.
Q10: What troubleshooting steps should I take when only three breakout links activate after installation? A: Verify the switch channelization configuration, reseat each SFP+ connector firmly, and examine DOM diagnostic readings to locate the faulty lane.
Q11: Can accidental compression or heavy pressure on the outer jacket destroy the internal fiber of this breakout AOC? A: Yes. Crushing the cable can fracture internal glass fibers. The outer jacket may remain intact while the optical transmission path is permanently damaged.
Q12: Does this long 15m breakout AOC add heavy weight and cause port sag on Cisco switch cages? A: No. AOC fanout cables are much lighter than copper breakout alternatives, eliminating mechanical strain and port sag on switch hardware.
Q13: Is it feasible to splice and repair this AOC locally if the cable jacket gets pinched or cut? A: No. Transceivers are pre-integrated into the cable assembly. Field splicing is not practical, and damaged units require full replacement.
Q14: What support is available if I receive breakout AOC with incorrect vendor coding after placing a bulk order? A: As your cisco qsfp+ to four sfp+ aoc active optical cable supplier, HYTOPTODEVICE provides exchange, return or re-programming service for coding compatibility issues upon delivery.
Q15: Can I request custom non-standard cable lengths instead of stocked standard sizes for my data center project? A: Standard lengths including 1m,3m,5m,10m,15m,20m,30m,50m are kept in stock. Custom lengths are available for enterprise orders subject to MOQ terms.
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every transceiver is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.





