Arista QSFP-100G-LR4 Compatible 100GBASE-LR4 100G QSFP28 LR4 Transceiver | HYTOPTODEVICE(10km, SMF, 1310nm, Duplex LC, DOM)
Product Overview
The Arista Compatible QSFP28-100G-LR4 is a premium 100G
QSFP28 LR4 transceiver, designed for high-speed 100Gbps connectivity up to 10km. Optimized for high-density data centers, this
100G module utilizes Single-Mode Fiber (SMF) and LAN-WDM technology(wavelength:
1295~1310nm) to ensure superior signal integrity. It features low power consumption, low latency and operates within a commercial temperature range (0°C to 70°C) for maximum reliability. Fully hot-swappable and DOM/DDM-supported, the interoperable 100G QSFP28 LR4 transceiver multi-vendor network provides seamless, cost-effective compatibility with Arista 7060X,7280R,7300X,7500R Series switches, making it the ideal choice for Arista leaf-spine fabric interconnection, cross-data-center DCI links and enterprise long-haul backbone upgrade
Key Technical Specifications
| Arista Compatible |
QSFP-100G-LR4 |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
QSFP28 |
Max Data Rate |
103.125Gbps (4x 25.78Gbps) |
| Wavelength |
1295.56nm,1300.05nm, 1304.58nm,1309.14nm |
Max Distance |
10km |
| Connector |
Duplex LC |
Transmitter Type |
4 x LAN WDM EML |
| Cable Type |
SMF |
Receiver Type |
PIN |
| Modulation (Electrical) |
4x 25G-NRZ |
TX Power |
-6.2~+2.5dBm |
| Power Consumption |
< 3.5W |
Receiver Sensitivity |
< -11.5dBm |
| Protocols |
100G Ethernet, MSA Compliant |
Operation Temperature |
0 to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
-
Fiber Choice: Works only with OS2 single-mode fiber. Multimode fiber is not compatible with this 1310nm CWDM4 module.
-
Distance Specification:Max 10km (OS2 SMF). Dirty end faces, excessive splicing and sharp bending reduce actual transmission distance.
-
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
-
Installation Specification: Hot-swap supported. Follow ESD anti-static procedures and keep LC connectors clean for stable links.
- Mode Setting: Configure 100G port speed via switch CLI. This LR4 module does not support breakout to 4×25G.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Network Hardware
1.Native Arista Compatibility
HYTOPTODEVICE 100G QSFP28 LR4 transceiver pass long-time traffic aging tests on official Arista platforms, realizing seamless replacement for QSFP28-100G-LR4 without port recognition errors, and all DDM monitoring data can be normally read on Arista EOS management page. Complete test logs and hardware verification videos can be provided for project inspection.
Compatible Arista Hardware:
- Arista 7050X / 7060X / 7280R Series Leaf-Spine Switches
- Arista 7500 Series High-Density Core Fabric Switches
- Arista DCS Data Center 100G Single-Mode Uplink Ports
- Arista Universal Spine Switch QSFP28 Expansion Slots
2.Multi-Brand Cross Compatibility
Built strictly to industry MSA standards, HYTOPTODEVICE’s QSFP-100G-LR4 breaks vendor lock-ins, delivering seamless interoperability across diverse network environments.
-
Open-Brand Devices (Plug-and-Play): 100% natively compatible with open-architecture brands like Ciena, Fortinet, Ubiquiti, MikroTik, D-Link, Zyxel, and more.
-
Locked-Brand Devices (Advanced Coding): Powered by our proprietary EEPROM writing technology, our modules successfully bypass vendor encryptions to ensure 100% compatibility with Cisco, H3C, Juniper, Dell, Intel, and the latest updated Arista firmware versions.
3. Free Value-Added Services
-
Custom firmware for multi-device compatibility
-
Support sample testing before bulk orders for project pre-verification
-
Private-label customization and professional deployment guidanc
-
Strict batch consistency quality control
- Free custom EEPROM programming for special and legacy network environments
- Free EEPROM rewriting (Tools Included) with 24/7 Tech Support
Primary Application Scenarios
- 100G QSFP28 LR4 transceiver bulk replacement for outdated Arista QSFP28-100G-LR4 modules during fabric bandwidth expansion
- Cross-data-center DCI interconnection using 100G QSFP28 LR4 transceiver to build low-loss 10km long-reach single-mode links
- Enterprise core backbone network construction deploying 100G QSFP28 LR4 transceiver for stable inter-room trunk transmission
- Large campus network iteration with low-jitter 100G QSFP28 LR4 transceiver for remote machine room 100G uplink
- System integrator custom coded 100G QSFP28 LR4 transceiver for multi-brand long-haul data center integration projects
- ISP edge room networking adopting standard-compliant 100G QSFP28 LR4 transceiver for 100G wide-area bandwidth expansion
Connectivity Solutions(Applications)
1. 100G Switch-to-Switch Interconnection

2.100G Switch-to-NIC Direct Connection

3.100G Long-haul Switch Link with Structured Cabling
The Core Features
1. Low Power & High Port Density
This HYTOPTODEVICE QSFP28 100G LR4 transceiver features low power consumption and high-speed, supporting high-density port deployment. It helps data centers fit more ports per rack without excessive heat buildup.

2. Host Validated for Reliable Interoperability
Each 100G transceiver plugs into target host switches directly without unsupported transceiver alarms and reduces project debugging time. Specific Compatibility Video available upon request.

3.Rigorous Full Testing & Stable Quality
Each unit passes optical calibration, high-low temperature burn-in and DDM inspection before shipment. HYTOPTODEVICE strict factory QC helps bulk buyers lower on-site failure risks. Curious how? Tour the
Test Center.

FAQ
Q1: How to eliminate unknown transceiver CLI alert displayed when deploying HYTOPTODEVICE 100G QSFP28 LR4 transceiver on network switches?
A: You can activate the device’s service unsupported-transceiver command, or send the module back to us for customized EEPROM firmware rewriting to eliminate identification failure alarms permanently.
Q2: Can vendor-coded 100G QSFP28 LR4 transceiver for different brands achieve normal optical interconnection on two ends of fiber links?
A: Yes. Custom EEPROM coding only impacts the matching between module and local switch. Our 100G QSFP28 LR4 transceiver fully complies with IEEE 802.3ba standards, guaranteeing complete line-side interoperability regardless of different brand coding on both sides.
Q3: What is the farthest reliable transmission distance of factory-tested 100G QSFP28 LR4 transceiver over standard single-mode fiber?
A: Our 100G QSFP28 LR4 transceiver supports stable 10km error-free transmission on regular G.652 single-mode fiber. When deployed on ultra-clean fiber with few splicing points, the effective transmission distance can extend to 11–12km for special project scenarios.
Q4: Is optical attenuation mandatory for short-span 1km and 2km links using commercial-grade 100G QSFP28 LR4 transceiver?
A: It depends on the maximum receiving power threshold of the module. If the transmitting optical power exceeds the device’s rated maximum Rx power over short distances, you must install a 3dB or 5dB fixed optical attenuator to protect the receiver chip.
Q5: What power dissipation classification do standard commercial HYTOPTODEVICE 100G QSFP28 LR4 transceiver conform to?
A: All our regular commercial 100G QSFP28 LR4 transceiver meet Class 3 power standard with power consumption below 3.5W. Low-cost generic modules and industrial temperature customized versions may reach Class 4 power dissipation up to 4.5W.
Q6: Is FEC error correction function compulsory to reach the rated 10km transmission range of IEEE-compliant 100G QSFP28 LR4 transceiver?
A: Based on IEEE 802.3ba official specifications, FEC is not a mandatory condition for 10km transmission of 100G QSFP28 LR4 transceiver. Most modern data center switches enable FEC by default to realize zero bit-error long-distance transmission.
Q7: What deployment compatibility benefits does multi-channel 100G QSFP28 LR4 transceiver own compared with single-lambda 100G LR1 optical modules?
A: Our 100G QSFP28 LR4 transceiver adopts 4×25G parallel optical lane design, which can be directly identified by all legacy 100G switches without extra accessories. 100G LR1 modules apply 1×100G PAM4 modulation, and older switch hardware needs matched gearboxes to decode signals normally.
Q8: What dedicated maintenance tools fit the LC duplex end face of factory-calibrated 100G QSFP28 LR4 transceiver?
A: We recommend standard 1.25mm one-click fiber cleaning pens or dust-free cassette cleaners for daily maintenance of our 100G QSFP28 LR4 transceiver LC ports, effectively removing dust without scratching optical contact surfaces.
Q9: What core laser chips are integrated inside commercial long-reach 100G QSFP28 LR4 transceiver for 10km single-mode links?
A: All HYTOPTODEVICE standard 100G QSFP28 LR4 transceiver are equipped with premium EML electro-absorption modulated lasers to guarantee stable long-distance signal transmission. Low-cost DML lasers cannot meet the signal integrity requirements of 10km 100G optical links.
Q10: Why do some generic 100G QSFP28 LR4 transceiver have extended delivery cycles amid global chip supply shortages?
A: Conventional LR4 optical modules rely on scarce special InP indium phosphide laser chips. Limited foundry production capacity leads to severe chip backlogs, while HYTOPTODEVICE maintains stable stock of complete laser components to shorten customer order lead time.
Packaging & Custom OEM Solutions
-
ESD Protection & Fast Shipping: Every module is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
-
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- Up to 70% cost savings vs OEM, transparent pricing & flexible bulk rates, supported quality returns
- 100% real-device compatible with Cisco, Huawei,Dell,Juniper, and Arista
- ISO 9001:2015 Shenzhen factory, full lineup: 1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T transceivers
- Ample stock, fast global DHL/FedEx shipping in 3–5 working days
- Free pre-sales engineering support for custom EEPROM & private label firmware
- Real switch test videos available for pre-purchase review; inspection & shipping videos provided per order
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

